In August 2020, a set of Wingoil portable hydro test pump was exported to Thailand. It’s an air-driven liquid pump system used for hydro test.Technical performances Medium:                                                                         Water Max. outlet pressure:                                                     80 bar @ 8 bar of driving-air Max. flow rate:                                                               4.42L/min Driving:                                                                          By compresed air Pump:                                                                            Pneumatic piston pumpPump model:                                                                  WYM10 Driving air pressure:                                                      8 bar Pressure ratio:                                                               1:10 Security valve:                                                               100 bar Inlet connection:                                                            1/2 NPT HP Outlet connection:                                                   1/4 NPT Dimension:                                                                    600mm×550mm×600mm Weight:                                                                          21kgsWingoil portable hydro test pump packControl panel with gauges & valvesStainless steel tubes, fittings and pump High pressure outlet with an anti-lost plug with chain

Hydrostatic Test Pump is designed to generate calibration pressures of up to 10,000 psi. It uses water or mineral-based hydraulic oil as a source for calibration of high-pressure input devices such as pressure transmitters or pressure gauges. Hydro testing a new water line essentially begins during the design phase. Understanding testing factors during design will enable the water professional to prepare for obstacles that may arise during the testing fire sprinkler hydrostatic test pump process.Hydrostatic Test requirements are set by considering the following:Flow/volume demandsSize and length of pipeThe total overall difference from the low to highest elevationsChanges in elevation or "high spots.hydro test pump specificationsHow To use Hydrostatic Test Pump?The hydrostatic test parameters must be clearly defined during the design phase and stated in the project specifications.Test pressure shall be 1.25 times the operating pressure. The duration of the test is two hours. Special consideration must also be given when multiple piping products are used.The test pressure of 300 psi will be detrimental to weak materials, such as polyvinyl chloride (PVC) rated at 125 psi, which also does not have a safety factor of 2 and surge allowance of 100 psi included in the design, compared to the stronger ductile iron that does.Any material not designed for the specific pressures should not be used and should be isolated from any section of a line to be tested at higher pressures.（hydrostatic test pump 15000 psi）How to build a hydrostatic test pump?Attention to Complete a Hydrostatic Test Pump Installation detail is of the utmost importance:Cleaning the bells, spigots, and gasketsProper lubrication of gaskets and spigotsUse of approved accessoriesMechanical Joint installation should include gasket lubrication, straight alignment, and specified bolt torqueProper alignment of joints during the homing process - "Straight is great!"Deflection of joints -after the pipe is homedAnyone who has searched for a leak will attest to the importance of proper installation. There is an extremely good chance that the most common installation, manual hydrotest pump.Hydrostatic Testing WARNING: The testing methods described in this section are for water-pressure testing only. These procedures should not be applied for air-pressure testing because of the serious safety hazards involved with compressed air. Also, pipelines intended for buried service should generally be tested with the backfill in place.Related products of Hydrostatic Test Pump:Product technical performances of Hydrostatic Test Pump:Max pressure:   700 psi @100 psi driving air pressureMax. flow rate:   6.36 L/MPump model:  WY-M07Pump type:   Single head single actingPressure ratio:  7:1Test medium:  Clean water, hydraulic oilDriven:   By compressed air Driving air pressure:  100 psiDriving air inlet:  NPT1/2FHP outlet:   NPT1/2FDimension:   600L×550W×600H(mm)Weight:   20kgsProduct Image Hydrostatic Test Pump：

In July 2020, a set of Wingoil portable CO2 filling pump was exported to Germany. It’s an air-driven liquid pump system used for filling CO2 in liquid. It’s equipped with a safety valve at the pressure of 100 bar.Technical performances Medium:                       CO2 in Liquid Max. outlet pressure:   80 bar @ 8 bar of driving-air Max. flow rate:              4.42L/min Driving:                         By compresed air Pump:                           Pneumatic piston pump Pump model:                WYM10 Driving air pressure:     8 bar Pressure ratio:              1:10 Security valve:              100 bar Inlet connection:           1/2 NPT HP Outlet connection:  1/4 NPT Dimension:                    600mm×550mm×600mm Weight:                          21kgs                Wingoil portable CO2 filling pump                Control panel with gauges & valves                Stainless steel tubes, fittings and pump                High pressure outlet with an anti-lost plug with chain

On July 1, 2020, two sets of Wingoil Hydro Test Pump Unit were delivered to Nigeria. The two units were both equipped with a stroke counter to count the stroke of the pump with max. working pressure of 17,000 psi. Wingoil Hydro Test Pump Unit is an air-driven pneumatic booster and injection pump system in a small and compact structure,  with the features of high pressure, high flow rate, and low failure rate. The high-pressure flow part of Wingoil equipment is made of 316 stainless steel material, which is suitable for various harsh environments. Technical performances:Brand:                              WingoilMax. outlet pressure:           17,000 psiWorking pressure:                15,000 psiMax. flow rate:                   1.49 L/MTest medium:                      Clean water, hydraulic oil, chemicalsPump type:                         Double head double actingPressure ratio:                     170:1Driving:                               By compressed air Driving air:                          100 psiDriving air inlet:                   NPT1/2FHP outlet:                            NPT1/2FDimension:                          800L×500W×550H(mm)Weight:                               43kgs                 2 sets of Wingoil Hydro Test Pump Uni                Wingoil hydro test pump unit is equipped with a stroke counter                Pressure regulator to adjust the inlet driving air from the air compressor                High pressure bleed-off valve to discharge the pressure after the test is finished