info@wingoil.com         +86-23-63089919         Send A Message

High Pressure Testing Equipment Manufacturers

by:Wingoil     2020-09-18

The Unit is air driven with pressures to 60,000 psi, obtainable in single and two pump fashions, and all stainless-steel wetted components. Hydrostatic pressure testing is fundamental in the life cycle of hydraulic pipeline systems.

Using unfiltered or impure water from a lake or pond with none treatment for pipeline hydrostatic stress testing has the possibility of damaging the pipeline. The pipe is not going to corrode instantly, however in the long run, if contaminated water flows in the pipeline in each hydrostatic check, then it could trigger corrosion and subsequently result in leakages.

Pump, Valves, Couplings and Pressure Gauge – A pump which is able to generating the desired design pressure of the pipeline is required for hydro-testing. The motor of the pump should have the ability to generate the design pressure. However, the ranking of the pump shall be depending on the pipe beneath remark and at what stress it will be routinely operated. The setup ought to have a stress gauge for measuring the strain inside the pipe. Couplings ought to be used to attach pipes in a absolute best method to eradicate any pressure drops.

In brief, it ensures that the pipeline is appropriate to be used in reliably serving its objective. You can observe the water leakage in the picture given below (Figure 1). It both stops the transfer of water from one place to another or reduces the strain to a great extent. So, to gauge the strength, performance, and durability of a pipeline, it's essential to carry out hydrostatic testing of the pipe. The Lorimer Portable Hydrostatic Test Unit is designed to be used within the shop or wherever pressure testing is required.

The management panel consists of pneumatic controls which operate a separate pump unit which could be mounted inside test space. This design isolates pumps and output stress parts away from the operator. The system is supplied with a dial air regulator to precisely achieve desired check pressures. For maximum safety, a momentary pneumatic toggle valve is used to control begin and stop of pumps to stop the operator from leaving controls and allowing the pump to run unattended.

JM Test supplies equipment for both digital and mechanical check procedures. With mechanical testing, you will typically need a pump, a temperature chart recorder for the vessel, a temperature and stress recorder for the testing agent, and a deadweight tester. JM Test additionally carries an entire line of “digital deadweight” tester gauges called Vaetrix. These gauges can simplify the testing process by charting all three required readings. This eliminates the necessity for a deadweight and two separate chart recorders.

Pipeline hydrostatic strain testing is carried out by charging the pipeline and then shutting off the provision valve for documenting observations in regards to the strain loss. Industries also execute it within the operational crops throughout shutdowns as part of the common maintenance process. A pipeline, whether or not it's a petroleum pipeline or water provide pipeline, must be free from defects and leakage factors in order that it could withstand the required stress. Pipeline hydrostatic testing ensures that the weld joints and flanges that be a part of the pipes are fitted properly by the fitters, and the fluid doesn’t leak out of the pipe. It additionally ensures that the material used within the pipeline has the required tensile strength to sustain the stress.

Hydrostatic strain testing shall be executed to a performance normal such as ISO, API, AS, ANSI or inside firm requirements. The DARTT Recorder is the totally transportable gear designed to qualify any hydrostatic pressure check towards the referenced commonplace, then routinely create a full traceability report. A Hydrostatic Test Pump is a self-contained, moveable, low quantity, high pressure pump powered by hand, air, electrical, or fuel engines, and with a high pressure hose linked to the gear. The pump is used to verify the element to be examined, is being crammed up with an incompressible liquid, normally water.

Hydrostatic testing starts by filling a container designed to hold strain. Vessels similar to pipelines, pipes and other containers may have hydrostatic testing. You can pump liquids like oil or water, that are almost incompressible, into the vessel.

Ideal for performing stress and leak checks on pure gas and propane piping techniques. Pressurize your system to a most of 15 psi and observe the needle. If the needle drops, that signifies that there's a leak within the system.
Custom message
Chat Online 编辑模式下无法使用
Chat Online inputting...